 |
Tankless Water Heaters and Space Heaters by Low Energy Systems (4) / Rubatex Information
FREE Lifetime Technical Support for gas, propane and electric tankless water heaters, space heaters, and vent-free appliances. 27+ years of experience. We stock parts, know how the heaters work and offer toll free technical assistance to our customers.
6. For running vent through combustible wall you will need the
Wall Thimble as a heat shield. 7. Order the
Termination . Screened 90 degree elbow used for
terminating vent pipe outside and to keep objects out of vent.
Please call 1-800-873-3507 with any question on ordering vent pipe.
Some situations vary so please ask questions.
Click to enlarge
pad 3" EZSeal Condensate Trap For Paloma PH16FS
+ Free Technical Support + Canadian
Residents + Se Habla Espanol
U.S. Toll-Free + 1-800-873-3507 ---------------------- Canada Toll-Free + 1-888-443-3847 pad Model PH-16FSN (Natural Gas) / PH-16FSP (L.P. Gas) Purpose Domestic Hot Water Supply Only / Residential Use Only Rated Gas Input (Btu/Hr.) 31, 500 (Min.) - 118, 000 (Max.) Dimensions, W x H x D 13 3/4" x 22 1/4" x 5 1/8" Net Weight (Ibs.) 35 Installation Indoor Wall Mounting Type (Forced Exhaust, Fan Assisted) Side wail venting for positive pressure and possible condensation With an optional vent trap for vertical venting (Max. 16 feet 5 inches) Working Water Pressure 14 psi (Min.) - 150 psi (Max.) Minimum Water Flow 0.92 Gallon/Minute Gas Connection 1/2" NPT Female (w/supplied Gas Shutoff Valve) Water Connection 3/4" NPT Male Vent Size 3" Special Certified Stainless Steel Venting Efficiency Rating 80% Inlet Gas Pressure before water heater Natural Gas: Min. 4.0" w.c. Max. 10.5" w.c. L.P. Gas: Min. 8.0" w.c. Max. 14.0" w.c. (Do not exceed maximum pressure.) Hot Water Supply Adjusting Range 100Ô~120Ô Combustion System Fan Assisted Combustion Main Burner Bunsen Type Burner Ignition Electric Continuous Sparking Electrical Portion Electrical Rating 120 V / 60 HZ, Less than 2 Amps Wire 3 (three) Pin Power Supply Cord 10 Feet Fuse 3 A Fuse x 2 Fan Motor Sirocco Fan Safety Devices Oxygen Depletion Safety Device Sensing Burner Flame Failure Safety Device Flame Rod Type Over Heat Limiter for Heat Exchanger Film Type for Entire Heat Exchanger Air Flow Switch Diaphragm Type Pressure Switch Max. Vent Pipe Extension 3" Diameter, 33 Feet 3 (three) 90 Degree Elbows Controlling System Water Volume Sensing Device, Water Volume Servo, Freeze Protection Electric Heater, Gas Pressure Regulator Optional Accessory Paloma Condensate Trap for Vertical Venting Hot Water Flow Rate and Temperature Rise Temp. Rise (Ô) 45 50 60 70 80 90 100 Water Flow (GPM) 4.2 3.8 3.2 2.7 2.4 2.1 1.9 Paloma PH16FS Hot Water Flow Chart
Tell a friend about this site + Free Technical Support + Canadian Residents + Se Habla Espanol
U.S. Toll-Free + 1-800-873-3507 ---------------------- Canada Toll-Free + 1-888-443-3847 pad Paloma PH28RIFS Tankless Water Heater TIV (Tankless Installation Valves) Dormont Flexible Gas Connector Pressure Relief Valve for Paloma Hot Water Heater Paloma PH24M Configuration and Dimensions + Free Technical Support + Canadian Residents + Se Habla Espanol
U.S. Toll-Free + 1-800-873-3507 ---------------------- Canada Toll-Free + 1-888-443-3847 pad Paloma Tankless Water Heater: Model PH-24M
Tell a friend about this site Any questions Call us at 1-800-873-3507, email us, or chat with us. Paloma PH28CDVS Specifications Sheet Air Intake Maximum Length 37.5 feet (with three 90-degree elbows) Net Weight 55 lbs. SAFETY ENGINEERING Carbon Monoxide Safety ICAD Proprietary system to monitor and optomize combustion (Not on Outdoor version) Heat Exchanger Overheat Protection Overheat Limiter Wrap. Resin Film that surrounds the heat exchanger. Flame Failure Thee separate flame rods to monitor flame failure Anti-boil Protection Temperature sensor Anti-scald Protection - Bath Controller maximum temp 120°F. - When on, Bath Controller takes priority over others. - While hot water is running, Bath Controller max. temp. cannot be raised above 112°F. FEATURES
Tell a friend about this site Any questions Call us at 1-800-873-3507, email us, or chat with us. Home | Search | View Cart | Package Tracking | Affiliate Program | Contact Us | FAQ | Testimonials PH12-123 Connector For Temperature Adjusting Spindle PH12-133 Gas Regulator & Valve PH12-39 PH12 Heat Exchanger PH12-159 Pilot Burner Assembly PH12-163 Sub-Pilot Burner PH12M-117 Water Regulator + Free Technical Support + Canadian Residents + Se Habla Espanol
U.S. Toll-Free + 1-800-873-3507 ---------------------- Canada Toll-Free + 1-888-443-3847 pad BENEFITS Unsurpassed thermal comfort IPEX WarmRite Floor gently warms the surfaces of objects, as well as the air itself. Heat loss from occupants is reduced. In addition, the higher temperature near the floor keeps feet warm, while the slightly lower temperature towards the ceiling provides greater comfort at head level. In fact, rooms are generally comfortable at a 3Î to 5Î (2Ê to 3Ê) lower than conventional settings. Convenience With no dry, hot-air drafts to cause fluctuations in humidity and temperature, the system can be adjusted precisely as desired - virtually set it, and forget it. And there are no restrictions on room design or furniture placement. Aesthetically beautiful No unsightly heat emitters, such as radiators or air vents. Quiet A properly designed radiant system generates no noise from the operation of forced-air fans or the sound of rushing air. The only sound is from the operation of the gas or oil burner on the boiler. Clean In contrast to forced-air systems, no dust, odors or germs are distributed throughout the building. With hydronic radiant heating, only 5% of the heat transfer is by convection. Room air circulation is extremely gentle, and does not aggravate allergy or asthma symptoms. Improved air quality IPEX WarmRite Floor has been approved for use in the American Lung Association Health House Project. There's no ductwork where particulates can hide. And warm floors eliminate the need for carpets which can hold dust and allergens. Extremely energy efficient Because hydronic radiant heating creates less air temperature stratification, comfort is sustained at lower temperatures. In addition, rooms are not pressurized as with forced-air systems, so air/heat leakage is reduced. Even by conservative estimates, energy savings are from 10% to 20%. Some projects have shown savings as high as 50% over traditional heating technologies. Long-term durability Corrosion, impact, crush and pressure resistant, the Kitec XPA composite tubing used in WarmRite Floor radiant heating systems is virtually indestructible. In fact, in-slab floor installations are as durable as the slab itself. Higher property value Installed during new construction or retrofitted in older buildings, hydronic radiant heating is seen as a luxury feature. And because there are no air ducts or vent, ceilings can often be made higher. + Free Technical Support + Canadian Residents + Se Habla Espanol
U.S. Toll-Free + 1-800-873-3507 ---------------------- Canada Toll-Free + 1-888-443-3847 pad HISTORY Hydronic radiant heating systems, using wrought iron and steel piping, originated in the early 1900's. During the 1940's and 50's, many radiant floor systems incorporating copper tubing in concrete slabs found widespread application. Though crude by today's standards, these systems proved they could deliver unsurpassed comfort. Some of the early systems are still in operation. However, over time many of them deteriorated and developed leaks due to corrosion. As a result, consumer confidence declined and with the advent of air conditioning in the late 1950's, forced-air heating experienced a broad resurgence. What changed the situation was the development of a new tubing made from cross-linked polyethylene (PEX). First used in Europe, then brought to North America in the early 1980's, these PEX systems proved once and for all that hydronic heating could deliver superior comfort, along with ease of installation and long service life. Hydronic radiant heating was here to stay. Today, IPEX WarmRite Floor radiant heating products such as our Kitec XPA composite pipe and PEX tubing are revolutionizing the radiant heating industry - incorporating advanced construction materials and controls to deliver comfortable, quiet, energy-efficient heating for end-users in a wide range of residential, commercial, industrial and institutional environments. + Free Technical Support + Canadian Residents + Se Habla Espanol
U.S. Toll-Free + 1-800-873-3507 ---------------------- Canada Toll-Free + 1-888-443-3847 pad HOW IT WORKS In a hydronic radiant heating system, water is distributed through a balanced, closed-loop, embedded piping network - usually constructed from cross-linked polyethylene (PEX) or PEX-Al-PEX composite tubing - and warmed by an appropriate heat source connected to all system loads. Modern hydronics can use virtually any type of heat source, including conventional boilers, wood-fired boilers, condensing boilers, tank-type water heaters, geothermal heat pumps or even thermal energy storage tanks. In a typical application, the piping throughout the system warms the floor surfaces, which act as radiant panels to emit heat into their respective rooms. Because there is no forced-air component to the system, convection is minimized. 95% of the heat is transferred by the radiating warmth of water, warming the room from the floor upwards. Furthermore, because radiant heat does not require a medium for transmission, it is non-directional. All objects in the radiant path are warmed uniformly, regardless of direction or placement. With the IPEX WarmRite Floor system, all of the rooms can be heated from the same hot water source. A wide selection of heating controls are available which make it possible to independently adjust the warmth in any room. WaiWela Tankless Installation Valves (TIV) are designed to save installation time while assuring that the installation is completed in a professional manner. The long term benefit is ease of maintenance and the ability to do the maintenance yourself if you desire. • Designed to work with Un-Clog-It Descaling Kit • TIV's are available in either 3/4" FNPT (thread) or 3/4" SWT (sweat) connection. • Allows for Full Diagnostic Testing of Heater *Does not include pressure relief valve *Designed for tankless water heaters with 3/4" water connections RESOURCES + Brochure (PDF) To download PDFs, right click on the link and choose "Save Target As" The Only Way to Install Any Tankless Water Heater TROUBLE FREE Makes installing your tankless water heater easy! Designed to save time and ensure that installation is completed in a professional manner. INCLUDED FUNCTIONALITY Designed for multiple functions, including: testing, maintenance, purging, flushing, and use with the Un-Clog-It Descaling Kit. VALUE-ADDED Future maintenance and descaling is now a simple job. Emergency shut off is as easy as a 1/4 turn of the color-coded ball-valve handle. Availability: Usually ships the next business day. WTIV1 pad US $126.97 pad Special Internet Price: US $95.00 pad Connection type: Choose Sweat Thread Stiebel-Eltron Mini Series [Sizing Chart]
U.S. Toll-Free + 1-800-873-3507 ---------------------- Canada Toll-Free + 1-888-443-3847 pad Stiebel-Eltron Mini Series [Technical Data] Model Mini 3 Mini 4 Mini 6
Tell a friend about this site Any questions Call us at 1-800-873-3507,
U.S. Toll-Free + 1-800-873-3507 ---------------------- Canada Toll-Free + 1-888-443-3847 pad Model PH-16FSN (Natural Gas) / PH-16FSP (L.P. Gas) Purpose Domestic Hot Water Supply Only / Residential Use Only Rated Gas Input (Btu/Hr.) 31, 500 (Min.) - 118, 000 (Max.) Dimensions, W x H x D 13 3/4" x 22 1/4" x 5 1/8" Net Weight (Ibs.) 35 Installation Indoor Wall Mounting Type (Forced Exhaust, Fan Assisted) Side wail venting for positive pressure and possible condensation With an optional vent trap for vertical venting (Max. 16 feet 5 inches) Working Water Pressure 14 psi (Min.) - 150 psi (Max.) Minimum Water Flow 0.92 Gallon/Minute Gas Connection 1/2" NPT Female (w/supplied Gas Shutoff Valve) Water Connection 3/4" NPT Male Vent Size 3" Special Certified Stainless Steel Venting Efficiency Rating 80% Inlet Gas Pressure before water heater Natural Gas: Min. 4.0" w.c. Max. 10.5" w.c. L.P. Gas: Min. 8.0" w.c. Max. 14.0" w.c. (Do not exceed maximum pressure.) Hot Water Supply Adjusting Range 100Ô~120Ô Combustion System Fan Assisted Combustion Main Burner Bunsen Type Burner Ignition Electric Continuous Sparking Electrical Portion Electrical Rating 120 V / 60 HZ, Less than 2 Amps Wire 3 (three) Pin Power Supply Cord 10 Feet Fuse 3 A Fuse x 2 Fan Motor Sirocco Fan Safety Devices Oxygen Depletion Safety Device Sensing Burner Flame Failure Safety Device Flame Rod Type Over Heat Limiter for Heat Exchanger Film Type for Entire Heat Exchanger Air Flow Switch Diaphragm Type Pressure Switch Max. Vent Pipe Extension 3" Diameter, 33 Feet 3 (three) 90 Degree Elbows Controlling System Water Volume Sensing Device, Water Volume Servo, Freeze Protection Electric Heater, Gas Pressure Regulator Optional Accessory Paloma Condensate Trap for Vertical Venting Hot Water Flow Rate and Temperature Rise Temp. Rise (Ô) 45 50 60 70 80 90 100 Water Flow (GPM) 4.2 3.8 3.2 2.7 2.4 2.1 1.9 Paloma PH16FS Hot Water Flow Chart
Tell a friend about this site + Free Technical Support + Canadian Residents + Se Habla Espanol
U.S. Toll-Free + 1-800-873-3507 ---------------------- Canada Toll-Free + 1-888-443-3847 pad Paloma PH28RIFS Tankless Water Heater TIV (Tankless Installation Valves) Dormont Flexible Gas Connector Pressure Relief Valve for Paloma Hot Water Heater Paloma PH24M Configuration and Dimensions + Free Technical Support + Canadian Residents + Se Habla Espanol
U.S. Toll-Free + 1-800-873-3507 ---------------------- Canada Toll-Free + 1-888-443-3847 pad Paloma Tankless Water Heater: Model PH-24M
Tell a friend about this site Any questions Call us at 1-800-873-3507, email us, or chat with us. Paloma PH28CDVS Specifications Sheet Air Intake Maximum Length 37.5 feet (with three 90-degree elbows) Net Weight 55 lbs. SAFETY ENGINEERING Carbon Monoxide Safety ICAD Proprietary system to monitor and optomize combustion (Not on Outdoor version) Heat Exchanger Overheat Protection Overheat Limiter Wrap. Resin Film that surrounds the heat exchanger. Flame Failure Thee separate flame rods to monitor flame failure Anti-boil Protection Temperature sensor Anti-scald Protection - Bath Controller maximum temp 120°F. - When on, Bath Controller takes priority over others. - While hot water is running, Bath Controller max. temp. cannot be raised above 112°F. FEATURES
- Continuous hot water on demand
- Energy-saving design
- Compact, and takes no floor space (wall hung installation)
- Unmatched Safety Engineering
- Proprietary ICAD Safety System (on indoor model)
- Propreitary Film Wrap Overheat Limiter (on heat exchanger)
- Flame failure and anti-boil protection
- Freeze protection to minus 30°F
- Built-in diagnostics and usage record
- Includes Digital Controller to set temperature and display diagnostics
- 180°F maximum temperature
- Power Return : AUTO-ON at last setting after power interruption
- Low NOx emissions meet SCAQMD rule 1146 requirements
- Can be used in circulation systems up to 140°F
Tell a friend about this site Any questions Call us at 1-800-873-3507, email us, or chat with us. Home | Search | View Cart | Package Tracking | Affiliate Program | Contact Us | FAQ | Testimonials PH12-123 Connector For Temperature Adjusting Spindle PH12-133 Gas Regulator & Valve PH12-39 PH12 Heat Exchanger PH12-159 Pilot Burner Assembly PH12-163 Sub-Pilot Burner PH12M-117 Water Regulator + Free Technical Support + Canadian Residents + Se Habla Espanol
U.S. Toll-Free + 1-800-873-3507 ---------------------- Canada Toll-Free + 1-888-443-3847 pad BENEFITS Unsurpassed thermal comfort IPEX WarmRite Floor gently warms the surfaces of objects, as well as the air itself. Heat loss from occupants is reduced. In addition, the higher temperature near the floor keeps feet warm, while the slightly lower temperature towards the ceiling provides greater comfort at head level. In fact, rooms are generally comfortable at a 3Î to 5Î (2Ê to 3Ê) lower than conventional settings. Convenience With no dry, hot-air drafts to cause fluctuations in humidity and temperature, the system can be adjusted precisely as desired - virtually set it, and forget it. And there are no restrictions on room design or furniture placement. Aesthetically beautiful No unsightly heat emitters, such as radiators or air vents. Quiet A properly designed radiant system generates no noise from the operation of forced-air fans or the sound of rushing air. The only sound is from the operation of the gas or oil burner on the boiler. Clean In contrast to forced-air systems, no dust, odors or germs are distributed throughout the building. With hydronic radiant heating, only 5% of the heat transfer is by convection. Room air circulation is extremely gentle, and does not aggravate allergy or asthma symptoms. Improved air quality IPEX WarmRite Floor has been approved for use in the American Lung Association Health House Project. There's no ductwork where particulates can hide. And warm floors eliminate the need for carpets which can hold dust and allergens. Extremely energy efficient Because hydronic radiant heating creates less air temperature stratification, comfort is sustained at lower temperatures. In addition, rooms are not pressurized as with forced-air systems, so air/heat leakage is reduced. Even by conservative estimates, energy savings are from 10% to 20%. Some projects have shown savings as high as 50% over traditional heating technologies. Long-term durability Corrosion, impact, crush and pressure resistant, the Kitec XPA composite tubing used in WarmRite Floor radiant heating systems is virtually indestructible. In fact, in-slab floor installations are as durable as the slab itself. Higher property value Installed during new construction or retrofitted in older buildings, hydronic radiant heating is seen as a luxury feature. And because there are no air ducts or vent, ceilings can often be made higher. + Free Technical Support + Canadian Residents + Se Habla Espanol
U.S. Toll-Free + 1-800-873-3507 ---------------------- Canada Toll-Free + 1-888-443-3847 pad HISTORY Hydronic radiant heating systems, using wrought iron and steel piping, originated in the early 1900's. During the 1940's and 50's, many radiant floor systems incorporating copper tubing in concrete slabs found widespread application. Though crude by today's standards, these systems proved they could deliver unsurpassed comfort. Some of the early systems are still in operation. However, over time many of them deteriorated and developed leaks due to corrosion. As a result, consumer confidence declined and with the advent of air conditioning in the late 1950's, forced-air heating experienced a broad resurgence. What changed the situation was the development of a new tubing made from cross-linked polyethylene (PEX). First used in Europe, then brought to North America in the early 1980's, these PEX systems proved once and for all that hydronic heating could deliver superior comfort, along with ease of installation and long service life. Hydronic radiant heating was here to stay. Today, IPEX WarmRite Floor radiant heating products such as our Kitec XPA composite pipe and PEX tubing are revolutionizing the radiant heating industry - incorporating advanced construction materials and controls to deliver comfortable, quiet, energy-efficient heating for end-users in a wide range of residential, commercial, industrial and institutional environments. + Free Technical Support + Canadian Residents + Se Habla Espanol
U.S. Toll-Free + 1-800-873-3507 ---------------------- Canada Toll-Free + 1-888-443-3847 pad HOW IT WORKS In a hydronic radiant heating system, water is distributed through a balanced, closed-loop, embedded piping network - usually constructed from cross-linked polyethylene (PEX) or PEX-Al-PEX composite tubing - and warmed by an appropriate heat source connected to all system loads. Modern hydronics can use virtually any type of heat source, including conventional boilers, wood-fired boilers, condensing boilers, tank-type water heaters, geothermal heat pumps or even thermal energy storage tanks. In a typical application, the piping throughout the system warms the floor surfaces, which act as radiant panels to emit heat into their respective rooms. Because there is no forced-air component to the system, convection is minimized. 95% of the heat is transferred by the radiating warmth of water, warming the room from the floor upwards. Furthermore, because radiant heat does not require a medium for transmission, it is non-directional. All objects in the radiant path are warmed uniformly, regardless of direction or placement. With the IPEX WarmRite Floor system, all of the rooms can be heated from the same hot water source. A wide selection of heating controls are available which make it possible to independently adjust the warmth in any room. WaiWela Tankless Installation Valves (TIV) are designed to save installation time while assuring that the installation is completed in a professional manner. The long term benefit is ease of maintenance and the ability to do the maintenance yourself if you desire. • Designed to work with Un-Clog-It Descaling Kit • TIV's are available in either 3/4" FNPT (thread) or 3/4" SWT (sweat) connection. • Allows for Full Diagnostic Testing of Heater *Does not include pressure relief valve *Designed for tankless water heaters with 3/4" water connections RESOURCES + Brochure (PDF) To download PDFs, right click on the link and choose "Save Target As" The Only Way to Install Any Tankless Water Heater TROUBLE FREE Makes installing your tankless water heater easy! Designed to save time and ensure that installation is completed in a professional manner. INCLUDED FUNCTIONALITY Designed for multiple functions, including: testing, maintenance, purging, flushing, and use with the Un-Clog-It Descaling Kit. VALUE-ADDED Future maintenance and descaling is now a simple job. Emergency shut off is as easy as a 1/4 turn of the color-coded ball-valve handle. Availability: Usually ships the next business day. WTIV1 pad US $126.97 pad Special Internet Price: US $95.00 pad Connection type: Choose Sweat Thread Stiebel-Eltron Mini Series [Sizing Chart]
+ Free Technical Support + Canadian Residents + Se Habla Espanol rubatex msds
U.S. Toll-Free + 1-800-873-3507 ---------------------- Canada Toll-Free + 1-888-443-3847 pad Stiebel-Eltron Mini Series [Technical Data] Model Mini 3 Mini 4 Mini 6
Phase 1 Voltage V 115-125 208 220-240 Wattage kW 3.0 2.6 3.5 4.3 5.7 Amperage A 25 12.6 15.2 20 24.7 Min. required circuit breaker size 30 Recommended wire size AWG Copper 10 12 Min. water flow to activate unit GPM/Lmin 0.53/2.0 0.85/3.2 Degree of protection according to IEC 529 IP 24 Min. water resistivity 2795 x in 11100 x cm Weight lbs / KG 3.44 / 1.56 Dimensions (HxWxD) in / (cm) 6.5 (16.5) / 7.5 (19.0) / 3.25 (8.2) rubatex neoprene
Working Pressure Psi / bar 150 / 10 Tested to Pressure 300 / 20 Volume of Water in Unit Gal / L 0.026 / 0.1 Water Connections for 3/8" O.D. flex connector rubatex pipe
Tell a friend about this site Any questions Call us at 1-800-873-3507,
email us, or chat with us. Home | Search | View Cart | Package Tracking | Affiliate Program | Contact Us | FAQ | Testimonials rubatex pipe insulation
072187 Well for Sensor (attaches to Solar Panel) CALL 1-800-873-3507 FOR MORE INFORMATION 073469 Stainless steel hose, insulated, for roof penetration 074274 Two frame rails (top & bottom) for ONE solar panel 074275 Two frame rails (top & bottom) for TWO solar panels 074278 Mounting hardware tile roof 074279 Mounting hardware metal roof 074280 45° rack for flat surface/roof mtg. rubatex 180
074281 Mtg hardware w/adj angle 074282 Connector for joining several collector banks 170804 U shaped copper tube for connecting two collectors rubatex 180 fs
monebaggasse- $ demand or tankless water heaters.
A recent DOE study showed energy savings of 25% to about 30% for water heating using such a system.
Read more
- How A Tankless Water Heater Can Cut Your Energy Bills
- Save Your Money With Tankless Water Heater
- Save Your Money With Tankless Water Heater
When the water heater is actually used to heat the water, the tank type water heaters are 40% to 60% energy efficient (the rest of the energy is spent to heat the exhaust and walls of the tank!), while tankless water heaters are 80% (gas) to 99% (electric) efficient. When you don't use hot water, you can save up to 15%-20% of your energy bill with the tankless water heaters, because tank type water heaters are subject to standby heat loss.
|
||||||||||||||||||||||||||||||||||||||||||||||||||
